APC RAID Subsystem SCSI-SATA II Manual de usuario Pagina 33
- Pagina / 259
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
SAS / SATA II NAS System
User’s Manual
33
Chapter 4 RAID Configuration Utility Options
Configuration Methods
There are four methods of configuring the RAID controller:
a.
VT100 terminal connected through the serial Monitor port
b.
Front panel touch-control buttons
c.
Web browser-based remote RAID management via the R-Link Ethernet port
d.
Telnet connection via the R-Link Ethernet port
NOTE: The RAID subsystem allows you to access using only one
method
at a time. You cannot use more than one method at the
same time.
4.1 Configuration through Terminal
Configuring through a terminal will allow you to use the same configuration options
and functions that are available from the LCD panel and via Telnet. To start-up:
1. Connect the Monitor port located at the rear of the system to another PC or a VT100
compatible terminal operating in an equivalent terminal emulation mode using serial
cable.
NOTE: You may connect a terminal while the system’s power is on.
2. Power-on the terminal.
3. Run the VT100 program or an equivalent terminal program.
- SAS/SATA II NAS System 1
- Table of Contents 2
- Preface 7
- FCC Compliance Statement 8
- Before You Begin 9
- SAS / SATA II NAS System 10
- User’s Manual 10
- Chapter 1 Introduction 11
- 1.1 Key Features 12
- 1.3 RAID Concepts 16
- RAID Management 20
- 1.4 Array Definition 21
- 1.5 High Availability 22
- 3.2 Powering On 28
- 3.3 Installing Hard Drives 30
- Main Menu 37
- Chapter 5 RAID Management 47
- 5.2 RAID Set Functions 49
- 5.2.2 Delete RAID Set 50
- 5.2.4 Offline RAID Set 54
- 5.2.6 Create Hot Spare 57
- 5.2.7 Delete Hot Spare 57
- 5.2.8 Rescue Raid Set 58
- 5.3 Volume Set Function 59
- 5.3.2 Create Raid 30/50/60 62
- 5.3.3 Delete Volume Set 63
- 5.3.4 Modify Volume Set 64
- 5.3.5 Check Volume Set 67
- 5.3.7 Stop Volume Check 70
- 5.4 Physical Drive 71
- 5.4.4 Identify Enclosure 73
- 5.5 System Controls 75
- 5.5.4 SNMP Configuration 79
- 5.5.5 NTP Configuration 80
- 5.6 Information Menu 84
- 5.6.2 System Information 85
- 5.6.3 Hardware Monitor 86
- PART II proNAS System 95
- Chapter 7 Introduction 96
- Chapter 8 proNAS Manager 104
- 8.1 Volume Manager 105
- 8.1.3 Volume Snapshot 118
- 8.1.3.3 Delete Snapshots 124
- 8.1.4 Volume Replication 126
- 8.1.5 iSCSI 134
- 8.2 Network Manager 142
- 8.2.2 Internet Gateway 146
- 8.2.3 SNMP/MRTG 147
- 8.2.4 Network Test 148
- 8.3 Account Manager 149
- 8.3.1.3 NIS Authentication 152
- 8.4 Share Manager 161
- 8.4.1 Share Management 162
- 8.4.1.2 Applying ACL 163
- 8.4.1.3 Modifying a Share 163
- 8.4.1.4 Deleting a Share 164
- 8.4.3 Protocol Setting 167
- 8.4.3.2 NFS 168
- 8.4.4.1 Group 169
- 8.4.4.2 Account 170
- 8.4.4.3 IP Address 172
- 8.4.6 Duplication 179
- 8.4.7 Default Share 183
- 8.5 System Manager 184
- 8.5.3 Report tab 187
- 8.5.4 Time tab 188
- 8.5.5 Serial Ports tab 189
- 8.5.6 Power tab 190
- 8.5.7 Reboot tab 191
- 8.5.8 Service tab 192
- 8.5.9 Status tab 195
- 8.6 Backup Manager 197
- 8.6.3 Tape Control 204
- 7. Click “Save” again 207
- 8.7 Log Manager 221
- 8.8 Event Manager 222
- Event Purpose 223
- Chapter 9 File Manager 225
- 9.2 Logon to File Manager 227
- Chapter 10 proBackup 231
- 10.3 Create Backup Plan 234
- 10.4 Restore Backup 240
- 10.5 Account Detail 241
- 11.3 ProNAS HA Properties 254
- 11.6 License Registration 258
- 11.7 Event Log Properties 259
Relacionado con productos y manuales para Redes APC RAID Subsystem SCSI-SATA II
Redes APC Metered Rack Guía de usuario
(110 paginas)
(110 paginas)
Redes APC WMR1000B Manual de usuario
(318 paginas)
(318 paginas)
Redes APC AP9606 Guía de usuario
(84 paginas)
(84 paginas)
Redes APC AP9613 Manual de instalación
(36 paginas)
(36 paginas)
Redes APC AP9470 Manual de instalación
(32 paginas)
(32 paginas)
Redes APC AP9622 Manual de instalación
(28 paginas)
(28 paginas)
Redes APC IP DSLAM Guía de usuario
(603 paginas)
(603 paginas)
Redes APC RAID Subsystem SCSI-SATA II Especificaciones
(100 paginas)
(100 paginas)
Redes APC AP9606 Manual de inicio rápido
(20 paginas)
(20 paginas)
Redes APC AP9312TH Guía de usuario
(32 paginas)
(32 paginas)
Redes APC AP9608 Manual de instalación
(32 paginas)
(32 paginas)
Redes APC Network Management Card AP9617 Guía de usuario
(150 paginas)
(150 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales