APC IP DSLAM Guía de usuario Pagina 420
- Pagina / 603
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
412
Valid values: 1 - 4294967295
srcportfrom
<srcportfrom-val >
Start port number of the range of source port
numbers. This field is invalid if 'srcportcmp' is
'any'.This field and 'srcportto' specify a range of
tcp source port numbers if 'srcportcmp' is either
'inrange' or 'exrange'
Type: Create -- Optional
Modify -- Optional
Default value: 0
srcportto <srcportto-val
>
End port number of the range of source port
numbers. This field and 'srcportfrom' specifiy a
range of TCP source port numbers if
'srcportcmp' is either 'inrange' or 'exrange'
Type: Create -- Optional
Modify -- Optional
Default value: 65535
dstportfrom
<dstportfrom-val >
Start port number of the range of destination port
numbers. This field is invalid if 'dstportcmp' is
'any'. This field and 'dstportto' specifiy a range of
tcp destination port numbers if 'dstportcmp' is
either 'inrange' or 'exrange'
Type: Create --Optional
Modify --Optional
Default value: 0
dstportto <dstportto-val
>
End port number of the range of destination port
numbers. This field and 'dstportfrom' specifiy a
range of tcp destination port numbers if
'dstportcmp' is either 'inrange' or 'exrange'.
Otherwise this field is invalid
Type: Create -- Optional
Modify -- Optional
Default value: 65535
srcportcmp eq | neq | lt
| leq | gt | geq | any |
inrange | exrange
Source port comparison type
Type: Create -- Optional
Modify -- Optional
Default value: any
dstportcmp eq | neq | lt
| leq | gt | geq | any |
inrange | exrange
Destination port comparison type
Type: Create -- Optional
Modify -- Optional
Default value: any
subruleprio low | high |
asinrule
This specifies the priority of the subrule. Based
on this priority value, the subrule is created in
fast or slow memory. In case priority is specified
as 'asinrule', subrule priority will be same as
specified in the rule.
Type: Create -- Optional
Modify -- Optional
Default value: asinrule
transporthdr ethernet |
pppoe
This specifies the type of the transport header in
the packet in which the corresponding IP is
being transported. If the value of this field is
'Ethernet', then the IP is being carried in the
Ethernet header. If it is 'PPPoE', then the
corresponding IP is being carried in the PPP
header.
Type: Create -- Optional
Modify -- Optional
Default value: Ethernet
Example $ create filter subrule tcp ruleid 1 subruleid 2 srcportfrom 21
srcportto 23 dstportfrom 21 dstportto 23 srcportcmp inrange dstportcmp
inrange subruleprio high
Output
Verbose Mode On
Entry Created
Rule Id : 1 Subrule
Id : 2
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Relacionado con productos y manuales para Redes APC IP DSLAM
Redes APC RAID Subsystem SCSI-SATA II Especificaciones
(100 paginas)
(100 paginas)
Redes APC AP9606 Manual de inicio rápido
(20 paginas)
(20 paginas)
Redes APC AP9312TH Guía de usuario
(32 paginas)
(32 paginas)
Redes APC AP9608 Manual de instalación
(32 paginas)
(32 paginas)
Redes APC Network Management Card AP9617 Guía de usuario
(150 paginas)
(150 paginas)
Redes APC 66123 Manual de instalación
(16 paginas)
(16 paginas)
Redes APC AP9630 Guía de usuario
(85 paginas)
(85 paginas)
Redes APC IP DSLAM Guía de usuario
(67 paginas)
(67 paginas)
Redes APC AP9630 Manual de usuario
(117 paginas)
(117 paginas)
Redes APC Network Management Card Guía de usuario
(118 paginas)
(118 paginas)
Redes APC AP9630 Manual de usuario
(32 paginas)
(32 paginas)
Redes APC AP9224110 Especificaciones
(16 paginas)
(16 paginas)
Redes APC AP9608 Especificaciones
(9 paginas)
(9 paginas)
Redes APC AP9608 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.119 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales