APC IP DSLAM Guía de usuario Pagina 459
- Pagina / 603
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
451
8.19.2 PPPoE Global Config Commands
8.19.2.1 Get pppoe global config
Description Use this command to get.
Command Syntax: get pppoe global config
8.19.2.2 Modify pppoe global config
Description Use this command to modify.
Command Syntax: modify pppoe global config
[ padimaxnumretries <padimaxnumretries-val> ]
[padrmaxnumretries <padrmaxnumretries-val> ] [ paditxintrvl
<paditxintrvl-val> ] [ padrtxintrvl<padrtxintrvl-val> ] [ wandntmrintrvl
<wandntmrintrvl-val> ] [ inactivitytmrintrvl <inactivitytmrintrvl-val> ]
[ discmaxnumretries <discmaxnumretries-val> ]
Parameters
Name Description
padimaxnumretries
<padimaxnumretries-
val>
Maximum number of times the PPPoE Client
sends a PADI for establishing a PPPoE Session.
Type: Modify －Optional
Valid values: 1 -10
padrmaxnumretries
<padrmaxnumretries
val>
Maximum number of times the PPPoE Client
sends a PADR for establishing a PPPoE Session.
Type: Modify － Optional
Valid values: 1 -10
paditxintrvl
<paditxintrvl -val>
The time, n seconds, between PADI retries from
the PPPoE Client.
Type: Modify － Optional
Valid values: 1 -60
padrtxintrvl
<padrtxintrvl-val>
The time, n seconds, between PADR retries from
the PPPoE Client.
Type: Modify － Optional
Valid values: 1 -60
wandntmrintrvl
<wandntmrintrvl-val>
The time, n seconds, for timeout of the WAN
Down Timer. The timer is started when the WAN
goes down, and if the timer times out, the session
is teared down. A value of zero for this timer
means it is not running.
Type: Modify － Optional
Valid values: 0 -
0xffffffff
inactivitytmrintrvl
<inactivitytmrintrvl-val>
The time, n seconds, for timeout of the Inactivity
Timer. The session can remain inactive for atmost
these n seconds after which it is teared down. A
value of zero means the timer is not running.
Type: Modify － Optional
Valid values: 0 - 0xffffffff
discmaxnumretries
<discmaxnumretries-
val>
The maximum number of times the PPPoE client
does a discovery stage for establishing a PPPoE
session. A trap is given to GAG on reaching this
number.
Type: Modify － Optional
Valid values: 1 -5
Example
$ get pppoe global config
Output
Max Total Sessions : 10 PADI Max Num Retries :
10
PADR Max Num Retries : 10 PADI Tx Interval :
5
PADR Tx Interval : 5 WAN Dn Tmr Interval :
10
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Relacionado con productos y manuales para Redes APC IP DSLAM
Redes APC RAID Subsystem SCSI-SATA II Especificaciones
(100 paginas)
(100 paginas)
Redes APC AP9606 Manual de inicio rápido
(20 paginas)
(20 paginas)
Redes APC AP9312TH Guía de usuario
(32 paginas)
(32 paginas)
Redes APC AP9608 Manual de instalación
(32 paginas)
(32 paginas)
Redes APC Network Management Card AP9617 Guía de usuario
(150 paginas)
(150 paginas)
Redes APC 66123 Manual de instalación
(16 paginas)
(16 paginas)
Redes APC AP9630 Guía de usuario
(85 paginas)
(85 paginas)
Redes APC IP DSLAM Guía de usuario
(67 paginas)
(67 paginas)
Redes APC AP9630 Manual de usuario
(117 paginas)
(117 paginas)
Redes APC Network Management Card Guía de usuario
(118 paginas)
(118 paginas)
Redes APC AP9630 Manual de usuario
(32 paginas)
(32 paginas)
Redes APC AP9224110 Especificaciones
(16 paginas)
(16 paginas)
Redes APC AP9608 Especificaciones
(9 paginas)
(9 paginas)
Redes APC AP9608 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales