APC IP DSLAM Guía de usuario Pagina 576
- Pagina / 603
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
568
Type: Create -- Optional
Modify -- Optional
Valid values: 0 -7
Additional Values: 8
Default value: 8
darpstatus Enable |
Disable
This specifies whether ARP packets received
on this VLAN are to be directed to a single
port using (VLANId, IP address) to bridge
port mapping learnt using DRA. This attribute
is effective in conjunction with the attribute
'gsvDot1dPortDirectedARP' of
'Dot1dBasePortExtTable' MO. ARP packets
are to be directed as mentioned above, only if
both the flags are enabled. If any of the two is
disabled, the ARP packets will be forwarded
as per the normal bridging flow.
Type: Create -- Optional
Modify -- Optional
Default value: enable
darpfailedhandling Drop |
TransparentForward |
FloodTrustedPorts
This specifies the action to be taken on an
ARP packet received on this VLAN for which it
is not possible to determine a single port
using (VLANId, IP address) to bridge port
mapping learnt using DRA. If the value is
drop, the ARP packet will be dropped. If the
value is Transparent Forwarding, the ARP
packet will be forwarded as per the normal
bridging. If the value is FloodTrustedPorts,
the ARP packet will be forwarded as per the
normal bridging, but only on ports that are
trusted.
Type: Create -- Optional
Modify -- Optional
Default value: FloodTrustedPorts
drabcasttoucast Enable |
Disable
This Parameter is used to configure whether
DHCP broadcast packet received for this vlan
will be converted to unicast packet or not.
Type: Create -- Optional
Modify -- Optional
Default value: Disable
bngmac <bngmac-val>
This is used to configure BNG Mac address of
this VLAN. If VLAN is configured to convert
DHCP broadcast packets to Unicast
packets,then this MAC address is used as
destination MAC address.
Type: Create -- Optional
Modify -- Optional
Default value: "\xff\xff\xff\xff\xff\xff"
drastatus Enable | Disable
This Parameter specifies the status of DRA
whether it is enabled for this Vlan or not. If
enabled DRA will Act as per the port
configuration on which DHCP packet is
received. If disabled DRA will not perform any
action on the DHCP packets received over
this vlan.
Type: Create -- Optional
- ADSL2+/G.SHDSL.bis 1
- IP DSLAM 1
- 1 About This Manual 9
- Document Conventions 10
- 2 What’s the difference 11
- DSLAM and IP based 11
- DSLAM? 11
- ADSL2/2+ IP DSLAM 12
- 3 Introduction 14
- 4 Getting Started 22
- 4.3 Hardware Installation 24
- 5 EMS Configuration 29
- 5.2 Windows Arrangement 40
- 5.3 Help 41
- 5.4 Tools Menu Introduction 42
- 6 Manage the ADSL2/2+ IP 59
- 6.2 Default Setting 61
- 6.3 System Information 62
- 6.4 Current Event 64
- 6.5 System 67
- 6.6 Configuration 67
- 6.7 DSL 73
- 7 Application Note 85
- Application Note 100
- 7.2 Advanced Configuration 114
- 8 System Administration with 143
- CLI Command - Action List 146
- Temperature State 152
- 8.2 802.1p Commands 153
- DefaultSVPriority : 1 154
- TrafficClass : 2 155
- RegenUserPrio : 1 156
- 8.3 ABOND Commands 157
- Entry Created 162
- 8.4 Aggregation Commands 165
- Get rdncy aggr info 175
- Create rdncy aggr info 175
- Delete rdncy aggr info 175
- Modify rdncy aggr info 175
- Get rdncy aggrport list 177
- Get rdncy aggr stats 178
- Reset rdncy aggr stats 178
- 8.5 ATM Commands 179
- Modify oam cc vc 180
- Verbose Mode Off: 184
- Output Fields 184
- Parameters 186
- 8.6 Bridging Commands 193
- Bridging Mode is Enabled 194
- Portid : 45 195
- Status : Mgmt 196
- Port Id : 2 207
- Set Done 214
- Egress ports : 1 2 221
- Group Learnt : 1 221
- 8.8 DHCP Commands 226
- 8.9 DSL Commands 228
- Example 230
- AtucChanGsB0dn : 10 238
- IntervalLESs(sec) : 10 256
- Tx Cap: Region1 294
- Output field 297
- • DSL Commands 326
- 8.10 EHDLC Commands 327
- 8.11 Ethernet Commands 329
- References 340
- • Ethernet stats command 340
- 8.12 EOA Commands 341
- • Ethernet commands 343
- • Ethernet Stats commands 343
- 8.13 Filtering Commands 344
- Get clfr namedlist genentry 347
- Create clfr namedlist map 349
- Delete clfr namedlist map 349
- <listid-val> 350
- Delete clfr profile branch 351
- Create clfr profile info 352
- Modify clfr profile info 352
- Create clfr profile node 353
- Delete clfr profile node 353
- Modify clfr profile node 354
- 356
- Mask : 0xffff 358
- <offset 364
- SetBase 368
- Create filter list genentry 371
- Delete filter subrule arp 388
- Id : 2 420
- • Generic Filter Commands 424
- 8.14 IGMP Commands 425
- Caution 437
- 8.15 Interface Commands 438
- IfName LinkUp/DnTrap 440
- 440
- 8.16 IP Commands 441
- RID : 1 449
- MacProfile Commands 451
- 0xffffffff 459
- DRA Nack Count : 50 469
- PIA global Status : Enable 484
- 8.21 QoS Commands 485
- Id : 1 500
- Thresh : 50 500
- 8.22 RMON Commands 503
- SUSPEND 504
- Get rmon mpool 505
- Pool Type : PARTITION 509
- Task Name : TSK1 509
- Mpool Name : FTSK143 509
- First Task 515
- 8.23 SNMP Commands 517
- 8.24 SNTP Commands 523
- 8.25 System Commands 525
- CP Bin Version : 1.6 541
- DP Bin Version : 1.8 541
- 0xFFFF 544
- Name– aal5-0 549
- Get system version 557
- 8.26 VC Aggregation Commands 560
- 8.27 VLAN Commands 564
- • GVRP Commands 567
- • VLAN commands 580
- 8.28 Miscelleneous Commands 581
- Download Completed 583
- Verbose Mode Off 585
- File removed 589
- File upgraded 589
- Over a maximum of 30 hops 594
- Trace complete 594
- 9 FD.cfg in detail 596
- 10 Supported mibs 602
Relacionado con productos y manuales para Redes APC IP DSLAM
Redes APC RAID Subsystem SCSI-SATA II Especificaciones
(100 paginas)
(100 paginas)
Redes APC AP9606 Manual de inicio rápido
(20 paginas)
(20 paginas)
Redes APC AP9312TH Guía de usuario
(32 paginas)
(32 paginas)
Redes APC AP9608 Manual de instalación
(32 paginas)
(32 paginas)
Redes APC Network Management Card AP9617 Guía de usuario
(150 paginas)
(150 paginas)
Redes APC 66123 Manual de instalación
(16 paginas)
(16 paginas)
Redes APC AP9630 Guía de usuario
(85 paginas)
(85 paginas)
Redes APC IP DSLAM Guía de usuario
(67 paginas)
(67 paginas)
Redes APC AP9630 Manual de usuario
(117 paginas)
(117 paginas)
Redes APC Network Management Card Guía de usuario
(118 paginas)
(118 paginas)
Redes APC AP9630 Manual de usuario
(32 paginas)
(32 paginas)
Redes APC AP9224110 Especificaciones
(16 paginas)
(16 paginas)
Redes APC AP9608 Especificaciones
(9 paginas)
(9 paginas)
Redes APC AP9608 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales